Raymarine C Series Manual do Utilizador Página 106
- Página / 244
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
92 C-Series Display Reference Manual
Important: Any offset entered will be applied to all charts on the chart card. You
should therefore ensure that this feature is switched off once you have transitioned off
of the errant chart. Any charting errors that you discover should be reported to
Navionics (see
page 201
).
To switch on chart offset:
Note:
If your vessel position is not available, the current chart centre is used as the ref-
erence point.
Changing the offset value
To change the offset value:
1. Select the Chart Offset function (see previous section)
2. Set the north/south offset value:
3. Set the east/west offset value:
Resetting the offset value
To reset the chart offset to zero:
1. Select the Chart Offset function (see previous section).
2. Reset to zero:
D7187-3
Alarm Setup Menu
Object Information Points ON
Vector Length Infinite
Datum WGS 1984
C
hart Offset..
.
Select Chart Offset
Toggle to ON
OFFSET
O
N
D7188_3
SET OFFSET...
ADJUST N-S
0ft
ADJUST N-S
-80ft
Adjust North/
South level as
required.
or:
D8384_1
ADJUST E-W
0ft
ADJUST E-W
121ft
Adjust East/ West
level as required.
OK
Press
Or
or:
81221_4.book Page 92 Tuesday, February 28, 2006 5:24 PM
- C-Series Display 1
- Reference Manual 1
- E-Series Reference Manual 2
- Important Information 3
- Disclaimers 4
- About this manual 5
- EMC conformance 5
- Multi-media chart cards 5
- Disposal 6
- Contents 7
- Contents vii 9
- Contents ix 11
- Contents xi 13
- Chapter 1: Overview 15
- Chart (Chapter 4) 16
- Fishfinder (Chapter 5) 16
- Radar (Chapter 6) 16
- Data (Chapter 7) 17
- Engine Monitor (Chapter 9) 17
- Navtex (Chapter 10) 17
- 1.3 The Simulator 18
- Chapter 2: General Operation 19
- 2.3 Using the controls 20
- Buttons and soft keys 21
- 2.4 Displaying applications 22
- Status bar 23
- Pop-up messages 23
- Data base lists 23
- Cartography Setup Menu 24
- ~ ` ´), the 25
- Status icons 26
- 2.6 Initial setup procedures 27
- Selecting a page set 28
- Selecting an application page 28
- Changing the active window 29
- Multiple to single window 29
- Single to multiple windows 29
- Day/night operation 30
- Backlight level 30
- 2.7 Using CompactFlash cards 31
- Inserting a card 32
- Removing a card 32
- 2.8 Managing data 33
- 3. Define data for saving 34
- 2. Select required list: 34
- Password confirmation 37
- Disabled data/functions 37
- Setting up a password 37
- 2.9 Emergencies and warnings 40
- Silencing a MOB 41
- Clearing a MOB 41
- Cancelling alarms 41
- 3.1 What is a waypoint? 43
- Waypoints on CDI windows 44
- 3.3 Placing a waypoint 45
- 3.4 Navigating to a waypoint 46
- Stop navigating to a waypoint 47
- 3.6 Editing a waypoint 48
- Changing waypoint details 49
- Moving a waypoint 49
- Erasing a waypoint(s) 50
- Erasing all waypoints 51
- 3.7 Sorting the waypoint list 52
- Making a new waypoint group 53
- Renaming an existing group 54
- My Waypoints 55
- Deep fishing 55
- Shallow fishing 55
- Reef fishing 55
- SHOW BY GROUP 56
- Chapter 4: Using the Chart 57
- Chart cards 58
- SHIP CURSOR 59
- 4.5 Where am I on the chart? 60
- 4.6 Moving around the chart 60
- Chapter 4: Using the Chart 47 61
- FIND NEAREST 62
- Displaying details of tides 63
- ... using the current diamond 64
- Chapter 4: Using the Chart 51 65
- ... using the port symbol 66
- Chapter 4: Using the Chart 53 67
- Chapter 11:Automatic 68
- Identification System (AIS) 68
- ... from your boat 69
- GOTO CURSOR 70
- STOP GOTO RESTART XTE 70
- Go to an existing waypoint 71
- Wait 10 seconds 72
- What is a route? 73
- What can I do with a route? 73
- Building a route 74
- Chapter 4: Using the Chart 61 75
- Highlight required 76
- Waypoint added to New Route 76
- Chart to Make Route dialog 76
- Make Route dialog to chart 76
- Saving routes 77
- Following a route 78
- Follow using the cursor 79
- Follow using the route list 79
- Follow in reverse order 79
- Viewing details of routes 81
- 4.11 Editing routes 82
- Make Route 83
- PLACE WAYPOINT 84
- Chapter 4: Using the Chart 71 85
- (see page 62) 86
- Erasing a route 87
- ... using chart vectors 88
- Chapter 4: Using the Chart 75 89
- ACQUIRE TARGET MARPA LIST 90
- OPTIONS 90
- Chapter 4: Using the Chart 77 91
- What is a track? 92
- How can I use tracks? 93
- Creating a track 93
- Creating a route from a track 94
- 4.16 Editing tracks 95
- Editing the selected track 96
- System chart view 97
- Local chart view 97
- North Up (N-up) 98
- Head Up (H-up) 98
- Course Up (C-UP) 98
- True motion (TM) 100
- Autorange 100
- Show/hide by group/symbol 101
- Show/hide waypoint name 101
- Show/hide waypoint index 101
- ... using the cursor 102
- ... via the route/track list 102
- Chapter 4: Using the Chart 89 103
- Chart Setup 104
- Chart Offset 105
- 106
- Cartography Setup 107
- FUNCTION 108
- 5.1 Introduction 109
- Gain mode 110
- Boat speed 111
- The depth of the target 111
- Seeing a live image 112
- I 113
- 5.4 Enhancing what you see 114
- Zooming in on the bottom 115
- Selecting the zoom factor 116
- Simplifying the bottom image 117
- Isolating bottom fish 118
- Pausing the scrolling image 120
- 5.5 Marking a position 121
- 200 kHz: Auto 122
- Gain: Auto High 122
- Measuring using VRMs 123
- 5.7 Fishfinder alarms 124
- Display settings 125
- Transducer Calibration 126
- DSM Setup 127
- Operating frequency modes 128
- Gain modes 129
- Adjusting the power setting 131
- To adjust the Power Setting: 132
- Chapter 6:Using the Radar 133
- Maximum radar range 134
- Side lobes 135
- Indirect echoes 135
- Multiple echoes 136
- Blind sectors 136
- Sea clutter 136
- Rain or snow clutter 137
- Interference 137
- (static icon) 138
- 6.4 The radar picture 139
- Head Up (H-UP) 141
- North Up (N-UP) 141
- Setting the motion mode 142
- True Motion (TM) 143
- 6.7 Getting the best picture 144
- Interference Rejection 146
- Expansion 147
- CLEAR WAKES 148
- CHART MODE AND 149
- ORIENTATION… 149
- CHART SYNC 149
- PRESENTATION… 149
- ... Using the range rings 150
- ... Using the cursor 150
- ... Using VRMs and EBLs 151
- Creating a VRM and/or EBL 152
- ... Using floating VRMs/EBLs 153
- Guard Zones 154
- 6nm Head-Up Relative Motion 155
- Rings 1nm 155
- 6nm Head-Up 156
- SAFETY NOTICES 157
- Introduction to MARPA 157
- How is a risk assessed? 158
- What happens to target data? 158
- Target display 158
- CPA graphics 159
- Setting up MARPA 160
- Acquiring a target to track 161
- Cancelling targets 161
- 6.11 Setting up your radar 162
- Highlight Radar 163
- Setup menu 163
- Enter Radar Setup 163
- Alarm Setup Menu 164
- 7.1 Introduction 165
- Pre-configured data panels 166
- Customize the panels 167
- Selecting cell data 168
- Merging a cell 169
- Indicator 171
- Steering instructions 172
- Fuel 1 Fuel 2 173
- Panel Setup Menu 174
- Panel Type 175
- Data content 175
- Chapter 10: Navtex 177
- 10.4 Viewing messages 178
- 10.5 Managing Navtex messages 178
- Sorting the message list 179
- 11.1Introduction 181
- 11.2What is AIS? 181
- Data details 182
- AIS status 183
- AIS Target symbols 184
- Viewing target information 185
- AIS List 186
- Viewing full AIS data 186
- Safe zones 187
- 11.7AIS Alarms 188
- Local AIS alarms 189
- Active alarm list 189
- 11.8Simulator 190
- 11.9AIS Layer Setup Menu 190
- EDIT PAGE SET 191
- Rename a page set 192
- Return to default setting 192
- 12.2 Changing the databar 193
- ON OFF 194
- ADD DATA 196
- MOVE DATA 196
- REMOVE DATA 196
- Application specific 197
- External equipment menus 197
- System-wide menus 197
- Date/Time Setup Menu 199
- Units Setup Menu 199
- System Integration Setup Menu 200
- US Gallons 200
- Imp Gallons 200
- SATELLITE DIFFERENTIAL 203
- WGS 1984 203
- OTHER SET UP 204
- Compass Setup 205
- Display Setup 205
- Databar Setup 206
- Select Page Set 206
- System Diagnostics 206
- Remove CF Card 206
- 13.1 Introduction 207
- 13.2 Maintenance procedures 207
- 13.3 Resetting the Display 208
- Settings and data reset 209
- Installation/Display 210
- Fishfinder 211
- Important Information 212
- World wide web 213
- For Navionics cartography 215
- Appendix A:Specification 217
- Radar Features 219
- Chart Features 220
- Fishfinder features 220
- Data features 221
- Engine monitor features 221
- Navtex features 221
- AIS features 221
- Interfacing 221
- , 85, 129 237
- Raymarine World Wide Warranty 239
- Limitations and Exclusions 240
- Other conditions 240
- Raymarine UK Ltd 241
- 4. Warranty limitations 242
- Raymarine Service Centers 244
Manuais e produtos relacionados com Recetor GPRS Raymarine C Series
Recetor GPRS Raymarine ST8002 Manual do Utilizador
(48 páginas)
(48 páginas)
Recetor GPRS Raymarine Chartplotter Manual do Utilizador
(101 páginas)
(101 páginas)
Recetor GPRS Raymarine A60 Manual do Utilizador
(50 páginas)
(50 páginas)
Recetor GPRS Raymarine Pathfinder Manual do Utilizador
(111 páginas)
(111 páginas)
Recetor GPRS Raymarine GPS Kit Manual do Utilizador
(24 páginas)
(24 páginas)
Recetor GPRS Raymarine 465 Manual do Utilizador
(107 páginas)
(107 páginas)
Recetor GPRS Raymarine ST80 Manual do Utilizador
(15 páginas)
(15 páginas)
Recetor GPRS Raymarine 320 Manual do Utilizador
(139 páginas)
(139 páginas)
Recetor GPRS Raymarine 300 Manual do Utilizador
(136 páginas)
(136 páginas)
Recetor GPRS Raymarine DSM30 Manual do Utilizador
(34 páginas)
(34 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais