Raymarine ST60 Especificações

ST60 Speed InstrumentOwner’s HandbookDocument number: 81037-5Date: 1 April 2004

viii ST60 Speed Instrument Owner’s Handbookproviding, to all other equipment on the SeaTalk network. A slave instrument is not directly connected to a

Preface ixParts suppliedUnpack your ST60 instrument and check that the following items are present:• Item 1, ST60 Speed instrument fitted with standa

x ST60 Speed Instrument Owner’s HandbookD4439-3ST60 SpeedInstrumentOwner'sHandbook1483232567910

Chapter 1: Operation 1Chapter 1: Operation1.1 Getting startedDisplayed informationYour ST60 Speed instrument provides the following:• Speed informatio

2 ST60 Speed Instrument Owner’s HandbookAverage speedThe average speed is reset at power up. It can also be reset manually by pressing the reset key f

Chapter 1: Operation 3Speed over groundSpeed over ground (SOG)information is available if your ST60 Speed instrument is part of a SeaTalk system to wh

4 ST60 Speed Instrument Owner’s HandbookWater temperatureThe water temperature is shown in either degrees Celsius or Fahrenheit, as set during calibra

Chapter 1: Operation 5Once you have selected the required timer display, press the reset key to start the timer running. When a timer is running, the

6 ST60 Speed Instrument Owner’s Handbook2. There are four preset illumination levels. Press the speed key to cycle through these levels until you reac

Chapter 2: Maintenance & Troubleshooting 7Chapter 2: Maintenance & Troubleshooting2.1 MaintenanceServicing and safety• Raymarine equipment sho

Raymarine, ST60 and SeaTalk are trademarks of Raymarine Limited© Handbook contents copyright Raymarine Limited 2004

8 ST60 Speed Instrument Owner’s HandbookCablingExamine all cables for chafing or other damage to the outer shield and, where necessary, replace and re

Chapter 2: Maintenance & Troubleshooting 9CAUTION: If you need to remove the transducer insert, have the transducer bung to hand and secure it in

10 ST60 Speed Instrument Owner’s Handbook

Chapter 3: Installation 11Chapter 3: InstallationThis chapter describes how to install the ST60 Speed instrument, and associated speed transducer. The

12 ST60 Speed Instrument Owner’s HandbookThe transducer types required for the various hull types are as follows:Other transducer types are also avail

Chapter 3: Installation 13• Have sufficient clearance inside the hull to fit the nut.• Have 4 in (100 mm) of headroom to allow for withdrawal.There mu

14 ST60 Speed Instrument Owner’s Handbook• It is at least 20 in (500 mm) from radio receiving equipment.• There is reasonable rear access for installa

Chapter 3: Installation 15Suppression ferritesThe following illustration shows typical cable suppression ferrites used with Raymarine equipment. Alway

16 ST60 Speed Instrument Owner’s HandbookFitting the instrumentThe ST60 Speed instrument can be installed using one of a number of different mounting

Chapter 3: Installation 175. Peel off the protective sheet from the self-adhesive gasket (4) then stick the gasket into position on the rear of the in

Preface iPrefaceImportant informationSafety noticesWARNING: Product installation & operationThis equipment must be installed and operated in ac

18 ST60 Speed Instrument Owner’s HandbookCAUTION: It is essential that only screws of the correct size are used to secure the instrument to the bezel

Chapter 3: Installation 193. Apply the flush mount template (supplied at the rear of this handbook) to the selected location and mark out the aperture

20 ST60 Speed Instrument Owner’s HandbookTo bracket mount your ST60 instrument, do so in accordance with the Control Unit Mounting Bracket Instruction

Chapter 3: Installation 21Connecting the instrumentTypes of connectionThe ST60 Speed instrument, can be connected:• As a stand-alone, master instrumen

22 ST60 Speed Instrument Owner’s HandbookPower supply connectionsSeaTalk systemsCAUTION: When instruments are connected to SeaTalk, ensure that the p

Chapter 3: Installation 23Stand alone instrumentsStand-alone instruments are not connected to SeaTalk and therefore need to be connected to an alterna

24 ST60 Speed Instrument Owner’s Handbook

Chapter 4: Calibration 25Chapter 4: Calibration4.1 IntroductionThe ST60 Speed instrument is set up with factory-programmed default settings, so in ord

26 ST60 Speed Instrument Owner’s Handbook4.2 User calibrationThe User calibration procedures enable you to:• Set the required units for speed readings

Chapter 4: Calibration 27speedtimereitherresetspeedtimerresetspeedtosheet 2&from sheet 2Useon each screen, except Adjust to SOGUser calibration -

ii ST60 Speed Instrument Owner’s Handbook

28 ST60 Speed Instrument Owner’s Handbooktimereitherresetspeedspeedspeedspeedto sheet 1Useon each screenD4367-2from sheet 1TemperatureunitsTemperature

Chapter 4: Calibration 29Setting the correct speedSet the displayed (current) speed using one of the following methods:• Use the Adjust to SOG screen

30 ST60 Speed Instrument Owner’s HandbookPop-up pilotSwitches the pop-up pilot function on and off.Leaving User calibrationHold down the speed and tri

Chapter 4: Calibration 31Intermediate calibration enables you to:• Check the instrument software version.• Check the instrument status - either MASTE

32 ST60 Speed Instrument Owner’s HandbookspeedtripSpeed calibration - sheet 1D4383-3timerresetandto save the cal factor Go to sheet 2PressExit speed c

Chapter 4: Calibration 337. At the end of the return leg, press the trip key. At this point:• The text START 2 alternating with the new calibration

34 ST60 Speed Instrument Owner’s Handbook8. Carry out one of the following actions:• If you are satisfied with the results of the first calibration ru

Chapter 4: Calibration 35speedspeedspeedspeedspeedSpeedresponseVMGresponseD4369-2timerresetandHold downspeed tripandfor approximately 12 secondseither

36 ST60 Speed Instrument Owner’s HandbookResponse settingsThe response values for both SPEED and VMG determine the frequency at which information

D4436-1Machine hole90mm (3.54in)diameterDrill 5mm (3/16in) diameterDrill 5mm (3/16in) diameterShaded areas to be removedTOPST60 Surface Mount Template

Preface iiiContentsPreface ...iImp

Shaded area to be removedTOP109 mmST60 Flush Mount Template114 mm4 holes6 mm diameterD4437-1

iv ST60 Speed Instrument Owner’s Handbook2.2 Troubleshooting ...8Pre

Preface vSetting the correct speed ... 29Adjust to SOG ...

vi ST60 Speed Instrument Owner’s Handbook

Preface viiIntroductionThank you for purchasing a Raymarine product. We are sure your ST60 instrument will give you many years of trouble-free operat